DESCRIPTION
Our high quality Factory Floor Paint has been formulated, tested and manufactured by Resincoat in the UK to ISO 9001 standard ensuring you achieve only the finest quality finish. Our high strength formula has been designed for use in industrial and commercial environments where there is aggressive foot and vehicle traffic. It is incredibly tough and resilient and is therefore able to withstand abrasion, static loading and any liquid or chemical spillages.
Resincoat factory floor paint can strengthen and improve your factory floor. Boasting a smooth, high gloss finish the coating is able to improve the appearance of your working environment. Additionally it is available in a huge range of colours allowing you to highlight specific working areas. Our high build epoxy formulation is up to 5x thicker than other floor paints on the market. This means your paint will maintain its colour and durability for longer. Many cheaper alternatives use a water based formula that will not be suitable for industrial conditions and are more likely to flake and peel within a few months.
COVERAGE RATES
Please see below for coverage rates. If you are coating a large area and would like expert advice, please call our team who will be happy to assist you.
1kg: 3-4m²
2.5kg: 8-10m²
5kg: 17–20m²
10kg: 35-40m²
Please note: the above coverage rates are per coat, in most cases we advise 2 coats.
APPLICATION GUIDE
Preparation
Old paint finishes should be removed if flaking at all and the surface should be sanded to create a texture (also known as a mechanical key) prior to applying Resincoat HB Epoxy Factory Floor Paint. When preparing for a floor coat, doing so mechanically (shot-blasting or grinding) is always advisable for best results, but if that is not possible then sanding the area or our Etch and Clean is a good alternative. After the surface has been completely abraded, thoroughly sweep and vacuum the area of any remaining dust or contaminants. For more information on preparation, please see technical data sheet.
Please note: Etch and Clean is only suitable for use on bare concrete.
Priming
• For new concrete floors or floors in good condition, prime with Resincoat Damp Tolerant Primer
• For dusty, old or weaker floors prime with Resincoat Deep Penetrating Primer
• For greasy floors with heavy oil residue clean thoroughly using a suitable degreaser scraping off any dust or dirt and then prime with Resincoat Oil Tolerant Primer
• For wood floors you should consider use of Resincoat Wood Floor Paint
Application
We advise when applying this product the ambient temperature is at least 7°C.
1. Mix Part A on its own with a mixing paddle attached to an electric drill for about 1 minute before adding ALL of Part B and continue to mix for another 90 seconds, keeping the paddle in suspension to avoid mixing air into the unit.
2. Pour entirety of the tin's contents into a plastic paint scuttle or tray.
3. Immediately begin applying your paint with a nylon-bonded resin suitable roller.
4. Use a brush around the edges to cut in (a second pair of hands can be useful for this stage).
5. As soon as the first coat has started curing (is no longer tacky to touch) you can re-coat; this should take 12-24 hours.
6. The cured final coat is ok for foot traffic. Cars and heavy objects, however, should be left off the new coating for the first 48 hours and chemicals including water should not be introduced for the first 7 days (Full chemical cure).
PLEASE NOTE: The pot life of this product is 20 minutes. This means that once parts have been mixed, the paint will start to chemically cure after this time. Ensure you remove the paint from the tin in this window. The paint will then be workable on your floor for up to 40 minutes.
Pot life = Time to harden in pot following addition of hardener
Working Time = Time to apply product before it becomes unworkable
USEFUL INFORMATION
• Roller sleeves should be used once per coat, two coats will require two roller sleeves.
• This product is NOT UV stable therefore can discolour when exposed to regular sunlight. For areas with plenty of repeated sunlight, please coat with a coloured UVR coating such as Resincoat Chemical Resistant UVR Floor Coating for a UV stable finish.
• This product should NOT be split. Taking smaller quantities from each tin, even if measured correctly, may cause issues with activating.
• This product is NOT self levelling.
• If you require a clear epoxy coating visit our clear epoxy product here.
